If the roller of the offset printing machine of a factory is full of ink and glue to dry the dirt, it becomes a "contact roller" during the pressing process, and the roller is stretched open, causing serious wear of the roller journal and bushing. Ghosts, bars, greasy and other faults occur at the same time. The angle of the scraper should be appropriate. The inclination of the metal scraper should be ≤23°-25°, and the inclination of the PE scraper should be slightly larger. The acetylated pyridine-glacial acetic acid-treated lignin sample (about 100 mg) was placed in a 5 ml-volume capped vial, 1 ml of pyridine was added, and the lid was tightened and mixed with a touch shaker to confirm that it was sufficiently dissolved, and then 1 ml of glacial acetic acid solution was added. Mix well and leave it in the dark for 24h. Because in the production process, the printer often adds water to the ink tank, causing the ink viscosity to drop. Mechanical properties of composite membranes The tensile strength of PLA composite membranes is affected by the addition of acetylated lignin to cresol. As shown in Fig. 4, the tensile strength of the composite membrane decreases first and then rises with the addition of acetyl acetate. In the gentle trend, the addition of acetic anhydride modified products showed a downward trend. Check if the printing plate pressure is normal and check if there is enough ink in the printing plate. Production process technical conditions 1 slurry ratio using 100% bleached sulfate softwood pulp (indicator: brightness 88%-90%, dust degree not more than 25mm2 / kg, fiber length not less than 0mm, pulp degree 13-15OSR) . According to the 2017 survey conducted by GEPResearch's “Water Treatment Membrane Industry Market Analysis Report”, in September 2000-2017, China had a total of 24,340 patents related to membrane technology (including inventions, utility models and appearances) (according to the number of publication days). Why do you want to pass the FSC forest certification? The acyl group and the hydroxyl group content of the lignin phenol are appropriately adjusted by the acetylation method, and a composite film having a certain mechanical strength can be obtained in the range of 5% to 20% of the lignin addition amount. What are the characteristics of the corrugated board, what are the characteristics of different types, and the influence of different types of scorpion combinations on the compressive strength.

Type B 楞: high plane pressure and low vertical pressure resistance. Seawater desalination desalination reverse osmosis membrane (RO) is used in advanced treatment of sewage, desalination, industrial water reuse and other processes. For example, there are 8 correction screws under the base of J2108, and the contact point of the screw is 200px square iron. After correcting the level, use the nut to fasten the base to prevent the foot screw from moving. The problem is: the base of the machine is not on the ground. Supported by 8 foot screws, because the oil pan is to be placed below, it is impossible to seal with cement. Therefore, the surface strength of the foundation is required to be high, and the specification uses 200 cement, and the actual use of 400 cement is better. And the steel bar is rolled on the upper layer of the foundation, otherwise the cement is easily damaged or cracked after the ground screw is touched, and the machine loses its level. Some factories have a refueling system, but they do not implement them. With the launch of the new brand jetscriptmetaLVPG1018, Mitsubishi HiTecPaper has launched a unique product: metallic silver gloss inkjet paper, developed for water-based inkjet printing, especially suitable for self-adhesive labels. To this end, we have developed and developed a reverse oblique blow type high efficiency hot air nozzle as shown in Fig. 3 (right). The smaller the 楞 type, the smaller the compressive strength of the carton and the smaller the amount of deformation. The cleaning degree of the cylinder surface of the large drying cylinder and the tightness of the scraper: the long-fiber low-slurry degree is relatively insufficiently combined with the paper fiber. If the large-cylinder scraper is not tight, the paper scraps are easily brought into the paper, causing hair loss. Attention company Pentair was established in 1966, dedicated to industrial wastewater treatment and desalination process, focusing on energy and resource recovery, and has rich membrane technology innovation and engineering experience. Therefore, under the conditions of satisfying the vertical and horizontal wet and dry strength of the paper and the normal production of the paper machine, the degree of beating is reduced as much as possible. When the paper is processed, the fine fibers are easy to fall off, resulting in hair loss, which is not conducive to the later hydroentangle compounding and use. Paper felt impact: The choice of press felt depends on the variety, quantitative and surface modification requirements of the paper produced. The spunlace base paper requires a fine surface and uniform consistency. Therefore, the choice of the blanket should give priority to the delicate surface of the blanket. Degree, in actual use, the ratio of wool net to felt is not less than 65%, and the ratio of surface fiber weight to wool net should not be lower than 30%, and the surface fiber fineness is not more than 8dtex, ensuring good surface modification. effect.

The special feature of the product is that metal-gloss inkjet labels previously used only metal foils. However, Jetscriptmeta LVPG1018 is a pure fiber paper product with a metal mirror and a transparent microporous inkjet coating that provides excellent print performance. The main features are: 110g /? O metal silver mirror high print density fast drying for water-based inkjet printing (dye and pigment ink) and latex ink compatible with the best performance in the self-adhesive production process (label production, labeling, mold Cut and discharge). It doesn't matter, continue to reduce the number of stacking layers. When I finally piled up to the third floor, Zengmenxiu began to use the stretch film to lay the foundation. This time, the carton was finally fixed.

Article source address: http://

Eyeshadow

What is the function of eyeshadow

1. Proper use of eye shadow can make your eyes more attractive, bigger and more beautiful, and make the whole makeup look three-dimensional and have the role of finishing touch.

2. In addition, when painting some special makeup, a large number of eye shadow will be used to highlight the look of the eyes. Usually, when making up in life, choose the color that you like and match with the color of Lipstick and clothing, touch a little eye shadow with your finger belly on the outer corner of the upper eyelid, and gently smear it from the outside to the inside. A simple wipe can make the whole person more colorful.

3. Eye shadow is a kind of color makeup, which is used to smear on the eye face (i.e. eyelid) and corner of the eye to produce shadow and tone contrast. Eye shadow is in powder, stick, paste, lotion, pencil and flake. The colors are very diverse, including blue, green, brown, tea, brown, and purple. Other colors are black, white, red, and yellow.

4. Eye shadow is a kind of cosmetics that can enhance the three-dimensional effect of the eye and modify the eye shape to set off the eye's radiance. It has rich colors and diverse varieties. Asian skin is yellow, and it is difficult to match eye shadow color. Therefore, we should follow the balance principle, balance the relationship between facial skin tone, hair color and eye color, and make us look radiant.

Eyeshadow,Eyeshadow Palette,High Pigment Eyeshadow

Suzhou Yimeijia368 Biological Technology Co.,Ltd. , https://www.yimeijiabeauty.com