This kit can only be used for scientific research, not for medical diagnosis.
Quantitative detection kit for rabbit soluble vascular cell adhesion molecule 1 (sVCAM-1) (ELISA)
user's Guide
[Rabbit soluble vascular cell adhesion molecule 1 (sVCAM-1) Elisa kit kit name]
Rabbit soluble vascular cell adhesion molecule 1 (sVCAM-1) quantitative detection kit (ELISA)
[Rabbit soluble vascular cell adhesion molecule 1 (sVCAM-1) Elisa kit kit uses]
Quantitative detection of soluble vascular cell adhesion molecule 1 (sVCAM-1) in rabbit serum, plasma and related liquid samples.
[Rabbit soluble vascular cell adhesion molecule 1 (sVCAM-1) Elisa kit detection principle]
This kit uses double-antibody two-step sandwich enzyme-linked immunosorbent assay (ELISA). Add the standard and the test sample to the pre-coated rabbit soluble vascular cell adhesion molecule 1 (sVCAM-1) monoclonal antibody transparent enzyme label coated plate. After incubation for a sufficient time, wash to remove unbound components Add enzyme-labeled working solution, and after incubation for a sufficient time, wash to remove unbound components. Substrates A and B were added in sequence, and the substrate (TMB) was converted into a blue product catalyzed by horseradish peroxidase (HRP), which turned yellow under the action of acid. The concentration of adhesion molecule 1 (sVCAM-1) was positively correlated. The OD value was measured at a wavelength of 450 nm. Based on the OD value of the standard and the sample, the content of soluble vascular cell adhesion molecule 1 (sVCAM-1) in the sample was calculated.
[Composition of Elisa kit of rabbit soluble vascular cell adhesion molecule 1 (sVCAM-1)]
1
Enzyme coated plate
12 holes × 8
7
Developer A liquid
6mL
2
Standard
0.3mL × 6 tubes
8
Developer B liquid
6mL
3
20 times concentrated washing liquid
25mL
9
Stop solution
6mL
4
Sample diluent
6mL
10
Instructions
1 serving
5
Special diluent
6mL
11
Sealing film
2 sheets
6
Enzyme reagent
6mL
12
sealed bag
1
Remarks: The concentration of standard products (No. 1 → No. 6) is: 320, 160, 80, 40, 20, 10 μg / L.
[Rabbit soluble vascular cell adhesion molecule 1 (sVCAM-1) Elisa kit required but not provided reagents and equipment]
1. 37 ℃ thermostat
2. Standard specification microplate reader
3. Precision pipettes and disposable tips
4. Distilled water
5. Disposable test tubes
6. Absorbent paper
[Rabbit soluble vascular cell adhesion molecule 1 (sVCAM-1) Elisa kit operating steps]
1. Preparation: Remove the reagent kit from the refrigerator and re-equilibrate at room temperature for 30 minutes.
2. Mixing solution: dilute the 20-fold concentrated washing solution with distilled water to the original one.
3. Add standard products and samples to be tested: take a sufficient number of enzyme-coated plates and fix them to the frame. Set up standard wells, sample wells to be tested and blank control wells, record the positions of each well in the standard wells. Add 50μL of standard product; first add 10μL of the sample to be tested, then add 40μL of sample diluent (that is, the sample is diluted 5 times); the blank control well is not added.
4. Incubation: Incubate in a 37 ° C water bath or thermostat for 30 minutes.
5. Wash the plate: discard the liquid, pat dry on the absorbent paper, fill each well with the washing liquid, let stand for 1min, shake off the washing liquid, pat dry on the absorbent paper, repeat the washing plate 4 times (you can also use the washing machine to press Instructions for washing the board).
6. Add enzyme-labeled working solution: add 50μL of enzyme-labeled working solution to each well, without adding blank control wells.
7. Incubation: Incubate in a 37 ° C water bath or thermostat for 30 minutes.
8. Plate washing: Discard the liquid, pat dry on the absorbent paper, fill each hole with the washing liquid, let stand for 1min, shake off the washing liquid, pat dry on the absorbent paper, repeat the plate washing 4 times (you can also use the washing machine to press Instructions for washing the board).
9. Color development: add 50μL of developer A solution to each well, and then add 50μL of developer B solution. Mix with a plate mixer for 30s (or shake gently by hand for 30s), and avoid color development at 37 ℃ for 15min .
10. Termination: Remove the enzyme labeling plate and add 50μL of stop solution to each well to stop the reaction (the color changes from blue to yellow).
11. Determination: Zero the blank holes, and within 15 minutes after termination, measure the absorbance (OD value) of each well with a wavelength of 450 nm.
12. Calculation: According to the concentration of the standard product and the corresponding OD value, calculate the linear regression equation of the standard curve, and then calculate the corresponding sample concentration on the regression equation according to the OD value of the sample. You can also use various application software to Calculation. The final concentration is the actual measured concentration times the dilution factor.
[Rabbit soluble vascular cell adhesion molecule 1 (sVCAM-1) Elisa kit sample requirements]
1. The sample cannot contain sodium azide (NaN3) because sodium azide (NaN3) is an inhibitor of horseradish peroxidase (HRP).
2. The specimen should be extracted as soon as possible after collection. The extraction should be carried out according to relevant literature. The experiment should be carried out as soon as possible after extraction. If the test cannot be performed immediately, the specimen can be stored at -20 ℃, but repeated freezing and thawing should be avoided.
3. The sample should be fully centrifuged, without hemolysis and particles.
[Rabbit soluble vascular cell adhesion molecule 1 (sVCAM-1) Elisa kit notes]
1. The experiment is carried out in strict accordance with the instructions, and the result of the experiment must be determined by the reading of the microplate reader.
2. If the enzyme-labeled coated board is not used up after opening, it should be put into a sealed bag and added with desiccant immediately.
3. It is recommended that all standards, samples and blank controls be tested in duplicate, and the average value is taken to reduce the experimental error.
4. Keep in mind that the sample has been diluted 5 times. The calculation result is multiplied by 5 to obtain the actual concentration of the sample.
5. The quantitative range of this kit is 10-320μg / L, if it exceeds this range, it is calculated by the extension of the standard curve. ), Multiplied by the total dilution factor is the final concentration of the sample.
6. If the color is too light, the substrate incubation time can be extended properly.
7. In order to avoid cross-contamination, the tips, samples and blank controls should be replaced with a new one for each addition; the common components such as enzyme working solution, sample diluent and substrate should be cantilevered, and they should not touch the microwells. ; Do not reuse the sealing film.
8. The kits are used within the warranty period, and different batches of reagents should not be mixed.
9. Substrate B is sensitive to light and avoid prolonged exposure to light.
[Rabbit soluble vascular cell adhesion molecule 1 (sVCAM-1) Elisa kit operating procedures summary]
Prepare reagents, samples and standards
Add prepared samples and standards, and react at 37 ℃ for 30 minutes
Wash the plate 4 times, add the enzyme reagent, and react at 37 ℃ for 30 minutes
Wash the plate 4 times, add color developing solutions A and B, and develop at 37 ℃ for 15 minutes
Add stop solution
Read OD value within 15 minutes
Calculation
[Rabbit soluble vascular cell adhesion molecule 1 (sVCAM-1) Elisa kit detection range]
10μg / L-320μg / L
[Rabbit soluble vascular cell adhesion molecule 1 (sVCAM-1) Elisa kit specifications]
96 servings / box
[Storage of rabbit soluble vascular cell adhesion molecule 1 (sVCAM-1) Elisa kit]
Store at 2-8 ℃, protected from light and moisture.
[Rabbit soluble vascular cell adhesion molecule 1 (sVCAM-1) Elisa kit expiration date]
6 months
We're one of the main Plastic Shopping Bags manufacturers in China. We has been specialized in custom Paper Bags for over 10 years for many famous brand: Levis, Spao, Zara, Chanel, Nike and Adidas. and JinYuan Plastic Grocery Bags is integrated flexible brand. Plastic Shopping Bags manufacturer with intention to provide a quick, environment friendly, quality consistent and cost effective flexible, brand honesty paper packaging solution. JinYuan is aimed to providing the best Plastic Shopping Bags brand logo color expression and helping build the brand honesty via bright color and trust-able Plastic Shopping Bags quality.
JinYuan Plastic Shopping Bags always takes the best modern making technology into your brand culture and by committing to invest in manufacturing technology and machinery: Heidelberg Printing Machine, Dark small Japan four folio colors printing machine, Roll Type Square Bottom Plastic Shopping Bags Machine to provide the best visual effect, and trust-able quality.
You can email artwork to us for an art proof of Small Plastic Bags before placing your order.
We prefer Plastic Grocery Bags artwork in .eps .ai or .pdf file formats, but if these are not available please email what you would like printed on the item.
Be sure to indicate the name and color of the item to be imprinted, along with the color ink you would like the imprint to be.
We will send you digital proof which must be approved before any imprinting is done.
1. We will organize mass production of Plastic Shopping Bags and shipping when you paid payment & freight at the same time as contract, let us know before paying and we will send you a invoice, Thank You!
2. If you have any questions about our Plastic Shopping Bags Please Email us we will be glad to answer your questions
3. Thank You For Stopping By Please Come Back To See Us Again!
Hope we'll have a pleasant cooperation in the near future.
Plastic Bags
Plastic Shopping Bags,Clear Plastic Bags,Plastic Grocery Bags,Small Plastic Bags
WenZhou JinYuan Packing Manufacture Co.,Ltd , https://www.tote-shoppingbag.com