SCREEN5055 error list

SET FILM MAG Cassettes not loaded, cassettes loaded
SET COLLECT BOX Cassettes Unloaded, Pack Receptacles
CHANGE COL BOX The film is not taken out of the cassette and the film is removed
MATERIAL EXIST Film position error, adjust film position
PLEASE CUT FILM Ejected film remains in the machine, execute CUT command
PLEASE SET FILM did not load film, execute the SET command
PLEASE LOAD FILM did not load film, execute LOAD command
FILM EMPTY1 film is used up, remove remaining film, load new film
FILM EMPTY2 film runs out, remove remaining film, load new film
SHUT THE DOOR The film runs out. Take out the remaining film and load the new film.
RESTART DL-MIDE restarts DOWNLOAD mode
FILM EMPTY3 film is used up, remove the remaining film, load new film
WIDTH NOT ENORGH The exposure width set by the computer is greater than the film width is greater than the film width, please enter the correct value
FAN1 TROUBLE Into fan 1 bad
FAN2 TROUBLE Bad Fan 2
FAN3 TROUBLE Into fan 3 bad
FAN4 TROUBLE Into fan 4 bad
AFP POWER OFF1 AFP power off, please open
AFP NOT READY AFP is starting, please wait
AFP POWER OFF2 AFP stop, turn on the power (standby)
AFP BUSY AFP is busy, please wait
DOWNLOAD ERROR Download Task Failed
MODE MIXMATCH Startup mode error, check DIP switch on MCON board
CHANGE FILM MAG Replacement Film Case
PUNCH DUST FULL Drill hole is full, clean up
IMPUT DATA ERROR The input data does not meet the exposure conditions, check the input data
LOADING ERROR The film is in the wrong position on the start sensor, adjust its position
FILM FAM1 film misplaced in middle sensor, adjust its position
FILM FAM2 film is misplaced in combination sensor, adjust its position

FILM FAM3 film is misplaced in the discharge sensor and adjusts its position
FILM FAM4 film stops in the wrong position of the discharge sensor and adjusts its position
FILM FAM5 film is in the wrong position at the end sensor and adjusts its position
FILM FAM6 film stops at the end sensor position and adjusts its position
Film cassette does not work during FILM FAM7 film transfer, adjust its position
FILM FAM11 film stops in the wrong position of the discharge sensor and adjusts its position
FILM FAM12 film is misplaced at the end of the sensor and adjusts its position
FILM FAM13 film stops at the end of the sensor. Adjust its position
FILM FAM14 film falls into AT unit and adjusts its position
MACHINE ERROR1 Partial error (sensor turned on or off)
MACHINE ERROR2 Partial error (cutting front sensor not turned on)
MACHINE ERROR3 Partial error (cut back sensor not turned on)
ERROR buffering error after MACHINE ERROR4 (the rear buffer guide sensor is not turned off and the rear buffer guide is not opened)
Buffering misdirection after MACHINE ERROR5 (the rear buffer guide sensor does not turn on and the rear buffer guide does not turn off)
MACHINE ERROR6 front buffering guide error (two or more front buffer guidance sensors are open)
MACHINE ERROR7 front buffering error (the sensor is not on when the current buffering guide is on)
MACHINE ERROR8 front buffering error (when the buffer buffer is closed, the sensor does not open)
MACHINE ERROR9 Front buffering error (the sensor does not open when the current buffering guide is in the REWIND position)
MACHINE ERROR10 AT Guide Sensor Not Closed, AT Guide Sensor Not Closed, AT Guide Not Open)
MACHINE ERROR11 AT Guide Sensor does not turn off, AT Guide Sensor does not turn on, AT Guide does not turn off)
MACHINE ERROR12 Exposure error (EXP-END signal not detected)
MACHINE ERROR13 ND conversion unit error (ND conversion sensor not turned on or off)
MACHINE ERROR14 Initial exposure error (page signal not turned on)
MACHINE ERROR15 Initial exposure error (No connection start pulse signal detected)
MACHINE ERROR16 Prism error (no prism acceleration signal detected)
MACHINE ERROR17 Front bumper detection sensor error (sensor fully open)
MACHINE ERROR18 The front bumper detection sensor is in error (the sensor does not open when the current bumper is raised)
MACHINE ERROR19 Front bumper detection sensor error (the sensor is not turned off when the current bumper is lowered)
MACHINE ERROR20 Front hole unit error (the front punch sensor is not turned on, the punch unit does not drop)
MACHINE ERROR21 Front hole unit error (the front punch sensor is not turned off, and the punch unit does not rise)
MACHINE ERROR22 Wrong end punch unit (the front punch sensor does not open, punch unit does not drop)
MACHINE ERROR23 Tail hole unit error (the front punch sensor is not turned off and the punch unit does not rise)

MACHINE ERROR24 The position of the pickup box is wrong
MACHINE ERROR30 Machine initialization error when power is turned on
STOP Presses the stop button and the operation stops
AFP ERROR1 &nb