Trouble analysis and elimination of paper loading unit

There are two types of common faults in the paper loading unit: one is caused by unqualified raw materials, such as the paper roll is not round and deformed, mainly caused by extrusion during transportation; the tension on both sides of the paper roll is not equal, and the surface of the paper roll is uneven Rope shape is a common problem in the production process, as long as the qualified paper roll is replaced, the fault can be eliminated. The second type of failure is caused by improper operation, such as paper breakage, wrinkles, etc., which are caused by the operator's insufficient understanding of the paper's adaptability.

Such faults can generally be eliminated by adjusting the tension controller.

Analysis and troubleshooting of printing unit

1. Common faults in water supply

Failure analysis: Excessive water supply makes the excess water on the printing plate too much, and the emulsification of the ink is accelerated, reflecting that the product is light in color, dull, dots are not full, and the color of the plate is unstable.

Remedy: First, check whether the depth of the bucket roller in the sink meets the requirements. If the depth is too deep, the water supply will increase, otherwise it will decrease. The bucket roller can be adjusted in the sink by the eccentric devices at both ends of the bucket roller The position of the water supply is normal: Secondly, check whether the pressure between the plate water roller and the plate cylinder is within the technical requirements. The specific method is to judge the ink inking plate of the plate when the plate cylinder is pressed The size of the pressure, the ink bar is generally suitable between 4-7mm, or use a 0.15mm thick feeler gauge to measure, and the adjustment can be achieved by adjusting the force with 2kg as the reference.

2. Common faults in ink

Failure analysis: Ink color instability manifests when the amount of ink on the printed sheet is large and small, extremely unstable, and difficult to control. This is because the gap between the ink rollers is too large, resulting in unstable ink layer on the surface of the ink roller, and the amount of ink supply changes accordingly.

Remedy: adjust the gap between each ink roller, can be measured with a feeler gauge of 0.1 5mm thick, and adjust with a force of 2kg. It should be noted that if the pressure adjustment between the ink rollers is too large, the frictional force will increase, and the ends of the ink rollers will heat easily damage the ink rollers; but if the pressure adjustment is too small, the ink supply will be unstable and cannot be printed normally .

3. Common faults in stamping part

Failure analysis: If the pressure is too low, the ink transfer is not sufficient, the product imprint is false, the dots are not full, the handwriting is missing, and the picture is not clear: too much pressure will reduce the printing plate's durability, and the handwriting, graphics and text Deformation increases the machine load.

Removal method: The method of changing the thickness of the blanket can be used, but under special circumstances, this method can not eliminate the fault or it is not ideal and incomplete. At this time, it is necessary to adjust the pressure (gap) between the rollers. It is necessary to refer to the random manual and mechanical schematic diagram to consult accurate technical data and adjust with special tools to make the pressure reach the technical index.

Failure analysis and elimination of folding unit

Failure analysis: The folding is not allowed, the specifications of the signatures do not meet the quality requirements, and the faults such as page falling, rotten pages, and paper jams occur. The wear of mechanical parts exceeds the technical requirements, the mechanical parts are damaged, and the moving parts are not adjusted properly, etc. will cause the above failures.

Remedy: First of all, observe the product carefully, because the faults can be expressed on the product. As long as you have an accurate understanding of the performance, function, and movement of each mechanical component, you can judge the specific location of the fault by observing the product; after determining the cause of the fault, you can check the corresponding component; by listening, touching, It seems that judging, watching carefully, and discovering problems. When the machine parts are damaged, the sound of movement will be unstable and the moving parts often have heat. The wear of the moving parts will result in the movement of the moving parts. These problems can be eliminated by replacing the parts.

EVA glass brush, eva brush , kitchen brush, dish brush , bottle brush , brush


We are professional manufacturer on cleaning products, covers like Spin Mop , Flat Mop , Spray Mop , Pva Mop ,window wiper,Cleaning Duster, Mop Holder , broom ,brush etc.
More than 20 patents of design and utility on mops, 100 workers, 10000sqm factory, 3000sqm non-dust workshop,
vendor of supermarket like ALDI,Woolworth,Target,etc, as seen as on tv shopping supplier, big wholesaler cleaning products supplier.
40minutes reach Ningbo port. ERP managment. We keep good quality and competitive prices for global valued customers always.
OEM and ODM for customer requirements,with our designer, 10years experience engineer of design structure,
tooling make, skilled workers of injection, good management of assembly line, complete QC inspection, strong sales team after service.
ISO9001, ISO14001 system passed,TUV,UL audited factory. BSCI audited, SEMETA certificate, GSV certificate.

Hope to work with you for mutual benefits.


EVA Glass Brush/Kitchen brush

EVA glass brush, eva brush, kitchen brush, dish brush, bottle brush, brush

Ningbo Dongsu Plastic Industry Co.,Ltd. , http://www.plasticproductmfg.com